An independent reference about aquarium equipment. It does not sell equipment, gives no veterinary advice and is not connected with the former site on this domain.

Guides

Practical guides

Most work with aquarium equipment comes down to a handful of recurring tasks: rinsing the filter without killing the beneficial bacteria, setting the light timer, checking a CO2 system before start-up and safely switching off the heater for a water change. Here these tasks are broken down step by step and in general terms. For details such as how the housing opens or where the seal sits, see the manual for your device.

A filter relies not on spotless sponges but on the bacteria living in them, so rinse it gently rather than scrubbing it clean.

— From the editors

How to use this section: the guides describe general principles that apply to most devices. If the manufacturer's manual differs from our description, follow the manual, because it was written for your model.

Guides

Tasks that sooner or later face everyone who keeps an aquarium with equipment at home.

Rinse a filter safely

Mechanical sponges are squeezed out until water flows freely through them again, while biological media are only lightly rinsed in tank water. Hot tap water kills the bacteria that process waste.

Problems

Set the photoperiod

A timer switches the light on and off at the same time every day, so the plants get the same amount of light day after day. The length of the photoperiod is adjusted gradually, watching the plants and any film on the glass.

Tools

Start CO2 injection

A pressurised system is switched on only after checking the joints, the check valve and the bubble counter. Gas runs while the lights are on, and at night the solenoid valve shuts it off on a signal from the timer.

CO2 reactor (Russian only)

Prepare for a water change

Before putting your hands in the water, unplug the heater, the filter and other equipment. Bring new water to the tank's temperature, and switch the heater back on only once it is fully under water.

Security

Place the air pump correctly

If the air pump sits below the water level, fit a check valve on the airline. Without it, water can siphon down the line when the power goes off and flood the pump and the floor.

Glossary

Keep a parameter log

Test results, water change dates, equipment maintenance, anything unusual you notice. A log helps you link changes in the water to what you did with the equipment instead of relying on memory.

Questions

Catalogue of English-language articles

This catalogue will collect standalone Akva-DV articles written specifically for English-speaking readers of the guide.

Coming soon

  • Planning a fish room or tank corner so sockets and cables stay dry
  • Keeping a tank stable through summer heatwaves and winter power cuts
  • Choosing between a canister and a hang-on filter for a planted tank
  • Getting your aquarium equipment ready before you go on holiday

Editorial rules

  • Articles in this catalogue are written separately for each language version and are not translations.
  • Some articles link to third-party websites, including gaming services; we do not control their content, prices or terms.
  • We do not sell equipment, and we do not publish advertising, rankings, prices or reviews.

How to service a canister filter

  1. Prepare the area and a container

    Lay a cloth or a tray on the floor under the cabinet, get a bowl and fill it with water from the tank. You will rinse the media in it, so do not use tap water for this.

  2. Unplug and close the taps

    First pull the filter's plug out of the socket, then close the taps on the hoses if there are any. This keeps the water in the hoses, so the housing can be disconnected without a puddle on the floor.

  3. Open the housing and remove the media

    Remove the lid as described in the manual and take out the baskets one by one. Remember or photograph the order of the sponges and media so you can put everything back in place.

  4. Wash mechanical, rinse biological media

    Squeeze the sponges and fine synthetic wool in tank water until it runs almost clear. Give the biological media only a light rinse to remove coarse dirt: the bacteria on their surface must stay.

  5. Clean the impeller and check the seal

    Take out the impeller and use a soft brush to remove slime from it and its housing. Inspect the sealing ring: if it is dried out, cracked or flattened, replace it with one the manual specifies.

  6. Reassemble, fill and restart

    Put the media back, close the lid, open the taps and let the housing fill with water. Then plug it in and listen: a steady sound and strong flow mean the air is out. Finally, inspect the joints and make sure nothing is dripping.

  • Tools

    Liquid drop tests and strips, a thermometer, a timer and a scheduled socket, a gravel vacuum with a hose and a parameter log: what helps and how to use it.

  • Comparisons

    Canister or internal filter, drop tests or strips, pressurised CO2 or a tank without gas injection: the pros, the hassle and who each option suits.

  • Problems

    A noisy filter, weak flow, cloudy water, algae film, a tank overheating in summer, an odd test result: what to check and in what order.

  • Security

    Water near sockets, a heater out of water, water siphoning back into an air pump, CO2 pressure, overheating cables and leaks into the flat below.

  • CO2 reactor (Russian only)

    A Russian-language memo on pressurised CO2 systems: the parts, checks before start-up and why you should never build a pressure vessel yourself.

Sources

  • Equipment manufacturers' instructions (in general terms)
  • General electrical safety rules (in general terms)
  • Editorial materials of the guide

Everything described here is stated in general terms and reflects the editors' understanding at the time of writing. The design of your particular filter, light or regulator may differ from our description. If the manual for your equipment says otherwise, follow it: it was written specifically for that device.