An independent reference about aquarium equipment. It does not sell equipment, gives no veterinary advice and is not connected with the former site on this domain.

Security

Safety

An aquarium brings together two things we normally keep apart at home: a lot of water and electricity. Add a hot heater, a pressurised cylinder and the neighbours in the flat below, and it is clear why safety matters more here than any setting. Most mishaps are prevented by simple habits: unplugging equipment before hands-on work, routing cables properly and inspecting connections on time.

The most reliable rule in fishkeeping is simple: plug out first, hands in the water second.

— From the editors

What this section covers: the risks faced by everyone who keeps an aquarium with equipment at home. We do not describe anything to do with wiring, sockets or the consumer unit as a do-it-yourself job: that is work for an electrician.

Risks

Situations in which aquarium equipment most often becomes dangerous to people, animals or the home.

Water and sockets

Sockets are placed above the tank or off to the side, cables are routed with a drip loop, and all equipment is powered from a circuit with an RCD, which cuts the power if current leaks. Leave the installation of sockets and RCDs to an electrician.

Glossary

Heater out of water

A heater switched on in air overheats quickly: the glass tube may burst at once or crack when it is back in the water. Switch it on only when fully submerged in its working position, and unplug it before every water change.

Problems

Back-siphoning into an air pump

If the air pump sits below the water level, water can run back down the airline and flood it after a power cut. A check valve on the line stops water flowing that way, and it is even safer to place the pump above the tank.

Guides

CO2 leaks and pressure

The cylinder is under pressure, and large amounts of carbon dioxide in a closed room are harmful. Use only a factory-made cylinder and regulator, test the joints with soapy water and secure the cylinder so it cannot fall over.

CO2 reactor (Russian only)

Overheating lights and cables

A light covered with fabric or squeezed under a lid overheats, and an extension lead with many devices plugged in heats up at the plugs. Leave an air gap around the light and do not plug all your equipment into one spot.

Tools

Leaks and the neighbours below

A dripping hose, a loosened tap or a cracked seam can flood the floor and the flat below. Put a leak sensor under the cabinet, inspect connections regularly and keep cloths and a bowl to hand.

Questions

Routine before hands-on work in the water

Before a water change, cleaning the glass or replanting, unplug everything that is in or above the tank: heater, filter, air pump, light. It helps when the plugs are labelled and all the aquarium equipment can be switched off with one switch on the extension lead.

When you have finished, dry your hands and any spilt water, check that the heater is fully submerged, and only then plug the equipment back in. Listen to the filter and look at the flow: if anything sounds different from usual, switch it off and sort it out before you walk away.

If something has already happened

If the RCD has tripped, do not keep switching it back on: find the cause by unplugging devices one at a time, and if that does not work, call an electrician. If a socket sparks or smells of burning, do not touch the water and cut the power to that circuit at the consumer unit.

If you spot a leak, cut the power, close the taps on the hoses, mop up the water and warn the neighbours below. If you suspect a CO2 leak, close the cylinder valve, air the room and do not restart the system until you have found and fixed the leaking joint.

  • Guides

    Step-by-step guides: servicing a canister filter, setting the photoperiod, starting CO2 injection, preparing for a water change. Plus the article catalogue.

  • Problems

    A noisy filter, weak flow, cloudy water, algae film, a tank overheating in summer, an odd test result: what to check and in what order.

  • CO2 reactor (Russian only)

    A Russian-language memo on pressurised CO2 systems: the parts, checks before start-up and why you should never build a pressure vessel yourself.

  • Glossary

    The nitrogen cycle, biological media, pH, KH, GH, drop checker, regulator, check valve, airlift and drip loop, explained briefly and plainly.

  • Questions

    Answers about the guide, about choosing and setting up equipment, about safety and about routine maintenance of aquarium gear.

Sources

  • Equipment manufacturers' instructions (in general terms)
  • General electrical safety rules (in general terms)
  • Editorial materials of the guide

Everything described here is stated in general terms and reflects the editors' understanding at the time of writing. The design of your particular filter, light or regulator may differ from our description. If the manual for your equipment says otherwise, follow it: it was written specifically for that device.