An independent reference about aquarium equipment. It does not sell equipment, gives no veterinary advice and is not connected with the former site on this domain.

Tools

Tools

For aquarium equipment to behave predictably, you need more than the equipment itself: a few simple monitoring tools too, such as water tests, a thermometer, a timer, a gravel vacuum and a log. They take up little space, but they are how you know the filter is coping, the heater is holding temperature and the light comes on on time. Below is what comes in handy and how to use it without frustrating mistakes.

A water test without a record is just a colour in a vial; written in the log, it becomes part of your aquarium's history.

— From the editors

What this covers: tools and techniques in general terms, without brand or model names. How to use a particular kit is explained in its instructions, and they are worth reading before your first test.

What comes in handy

A small kit for monitoring water and equipment that is handy to keep next to the tank.

Liquid drop tests

A set of reagents and a test vial: reagent is added drop by drop to a measured water sample and the colour is compared with a chart. Drop tests are more accurate than strips and let you check pH, KH, GH, nitrite and nitrate separately.

Comparisons

Test strips

A strip is dipped in the water and, after the time given in the instructions, its pads are compared with a colour chart. This makes it easy to spot an obvious deviation, but for fine-tuning it is better to confirm the result with a drop test.

Comparisons

Thermometer

A separate thermometer is needed even if the heater has a thermostat: it shows what is really happening in the water. Place it away from the heater so you see the overall temperature, not the warm current.

Problems

Timer and scheduled socket

A timer switches the light, the CO2 solenoid valve and other devices on a schedule. The photoperiod stays the same and gas runs only while the lights are on, even when you are away. Choose a timer rated for the power of the equipment you plug in.

Guides

Gravel vacuum and hose

A gravel vacuum with a wide tube lifts dirt from the substrate during a water change, and a long hose helps you drain and refill without carrying buckets through the house. Keep them for the aquarium only, so no household chemicals get into the water.

Guides

Parameter log

A notebook or spreadsheet where you record test results, temperature, and the dates of water changes and equipment maintenance. The log reveals slow changes and which of your actions they followed.

Questions

How to do a drop test properly

  1. Read the kit's instructions

    The procedure, the number of drops and the waiting time vary between kits. Read the instructions to the end before you begin, and check the expiry date: old reagents give the wrong colour.

  2. Take the sample correctly

    Draw water from mid-depth, not from the very surface and not straight from the filter outflow. Rinse the vial with the same water, then fill it exactly to the mark.

  3. Drip evenly

    Hold the bottle vertically so the drops come out the same size, and count them. An air bubble instead of a full drop is a common cause of an odd result.

  4. Wait the full time

    Cap the vial, mix as the instructions say and wait the stated time. Reading the colour too early or too late distorts the result.

  5. Compare the colour in good light

    Look at the vial against the white part of the chart in daylight or neutral light. Under the coloured light of an aquarium fixture it is easy to confuse shades.

  6. Record the result and wash the vial

    Enter the value in the log straight away, with the date and notes on any water changes or maintenance. Rinse the vial with clean water without detergent and let it dry.

What to check and how often

In a new tank, while bacteria are still colonising the filter, ammonia and nitrite are tested often, sometimes several times a week: this shows how the nitrogen cycle is progressing. Once the readings have settled, a weekly check of nitrate, pH and KH is usually enough, and general hardness, GH, is checked less often, for example once a month.

An extra test is needed after any noticeable change: replacing filter media, starting or readjusting CO2 injection, power cuts, cloudy water or unusual behaviour of the tank's inhabitants. If you inject CO2, watch pH and KH together: dissolved gas lowers pH, while KH shows how well the water resists such shifts.

  • Guides

    Step-by-step guides: servicing a canister filter, setting the photoperiod, starting CO2 injection, preparing for a water change. Plus the article catalogue.

  • Comparisons

    Canister or internal filter, drop tests or strips, pressurised CO2 or a tank without gas injection: the pros, the hassle and who each option suits.

  • Problems

    A noisy filter, weak flow, cloudy water, algae film, a tank overheating in summer, an odd test result: what to check and in what order.

  • Glossary

    The nitrogen cycle, biological media, pH, KH, GH, drop checker, regulator, check valve, airlift and drip loop, explained briefly and plainly.

  • Questions

    Answers about the guide, about choosing and setting up equipment, about safety and about routine maintenance of aquarium gear.

Sources

  • Equipment manufacturers' instructions (in general terms)
  • General electrical safety rules (in general terms)
  • Editorial materials of the guide

Everything described here is stated in general terms and reflects the editors' understanding at the time of writing. The design of your particular filter, light or regulator may differ from our description. If the manual for your equipment says otherwise, follow it: it was written specifically for that device.